https://pinballcars.com Fri, 14 Aug 2026 15:07:56 +0000 en-US hourly 1 https://wordpress.org/?v=4.1.1 https://pinballcars.com/budget-4k-virtual-pinball-machine-pc-vpx-rtx-2070-gpu-9th-gen-i7-cpu-16gb-atg4k-2/ https://pinballcars.com/budget-4k-virtual-pinball-machine-pc-vpx-rtx-2070-gpu-9th-gen-i7-cpu-16gb-atg4k-2/#comments Fri, 14 Aug 2026 15:07:56 +0000 https://pinballcars.com/budget-4k-virtual-pinball-machine-pc-vpx-rtx-2070-gpu-9th-gen-i7-cpu-16gb-atg4k-2/ Continue reading: BUDGET 4K Virtual Pinball Machine PC VPX RTX 2070 GPU 9th gen i7 CPU 16gb ATG4k]]>












This Was a lightly used Alienware R8, converted for Vpin use! Alienware Aurora R8 (water cooled CPU). Intel i7 9700 CPU. 512GB NVME (also has a 3.5 slot, and 2x 2.5 slots for more hard drive expansion). (dell/alienware has a downloadable control center to change the LED’s on the case). Please note, you must provide your own screens, this is ONLY the computer tower. This runs a a 4k 60hz playfield, and 2 additional screens, super smooth. This build is designed specifically for this setup, which you MUST have. 4k play field running 60hz. A 1080p backglass monitor. A 16:9 ratio 3rd screen for FULL DMD at 1366×768 (these 3 resolutions work perfect with a ATG 4K). (i can provide recommendations on screens if needed). NO USB MONITORS, must run though video card. Your screens need to remember the power state, so when you kill power, and apply power, they auto come on again. (all pc monitors do this, but some TV’s cant, and require a remote to power on each time). Screens must up and running before windows boots, or your screens re-arrange each time, and you have to re-configure. You have growing room even on this budget build, it runs everything currently released, near perfectly. Even On the most demanding vpinworkshop tables, CPU and GPU handle all the current tables at full 60FPS. Every table will run pretty much stutter free, and never drops from 59-60FPS. (In a rare event of a lot of flashers, and ball movement, you may see slight ball stutter, Ive only seen it on the new DIE HARD). This machine can be sent to you in several different ways. BLANK, ready for you to install your own OS/Software. Clean os install, ready for you to install pinball software. You have no idea where to start, and want me to take care of everything for you, and make your life as easy as possible.. Please shoot me a message and ask for details on what I can do for you. I provide good instructions and after sales support! (please see my feedback). Ive built 30 plus pincabs, Ive been working in IT for 20+ years. I want to sell this to someone that’s putting together a virtual pinball cabinet and needs a capable computer for a good deal, and can get up and going QUICK. Please be familiar with the programs that run all this, and have some decent computer skills, its not hard, but you need to know your way around windows. I have over a dozen people use this with ATGAMES 4K Cabinets, this worked perfectly! For ATG4k, The buttons will use “XPADDER” from what Ive read, Wagners Tech Talk covers everything Atgames4k related, so i highly recommend his youtube channel! Here’s some info on my own setup, that I run on my own machine. I do the L. Atest baller installer, with VPX 10.7, 10.8, with the latest pinmame, b2s, and flex/ultra dmd. I run Future Pinball to play the amazing pinevent tables (about 10 of them). Im running DOF configured and working with my test setup (a sainsmart 8 relay board). Im very much on QUALITY over quantity, so I have about 300 of the latest tables for myself. I have Colored rom support, (vni, pac, and the crz/serum, and new serum V2 format). All VPX and FP tables have had preview videos recorded for playfield, and backglass. That took me DAYS to do, this took a LOT of time getting about 700 videos recorded for pinup popper. As far as this machine goes. You need to be decent at using computers, installing games and software, basic use and understanding, this is 7 or 8 programs all working together the best they can, and you will have to make adjustments, troubleshoot, and so on, over time, as needed, when owning a vpin cabinet. The biggest part of this hobby is playing with everything and learning how it works. A backup Hard drive copy WILL BE INCLUDED. I recommend you make a full copy of the SSD drive, before you make any changes, this will save your life when you do updates and upgrades later on, if it goes sideways. I also sell plunger kits/input/nudge boards, i can discount that if bought at the same time.

]]> https://pinballcars.com/budget-4k-virtual-pinball-machine-pc-vpx-rtx-2070-gpu-9th-gen-i7-cpu-16gb-atg4k-2/feed/ 0 https://pinballcars.com/table-top-virtual-pinball-machine-24-full-hd/ https://pinballcars.com/table-top-virtual-pinball-machine-24-full-hd/#comments Sat, 01 Aug 2026 22:19:38 +0000 https://pinballcars.com/table-top-virtual-pinball-machine-24-full-hd/ Continue reading: Table Top Virtual Pinball Machine 24 FULL HD]]>


A virtual pinball machine offers all the fun and excitement of traditional pinball, but in a simulated environment. Custom-made Virtual Pinball cabinets, This means your order is built from the ground up by hand, (“stock numbers” represent build slots, not units on hand). Custom-made Virtual Pinball cabinets. Complete Plug and Play! Compatible with over 1000. No headache trying to figure out how to just simply play your new Virtual Pinball machine! Real glass Playfield Cover, no Lexan! Free custom Graphics: This will be from my list or files you provide to me (Files must be highest quality for large printing). Table Top Virtual Pinball Machine. 24 1080p HD LED Playfield. 20 1080p LED Backglass Monitor. B Solid State Drive. GeForce GTX Graphics Card. Please contact me with any questions or custom requests.

]]> https://pinballcars.com/table-top-virtual-pinball-machine-24-full-hd/feed/ 0 https://pinballcars.com/new-4k-virtual-pinball-machine-pc-vpx-rtx-5060-gpu-ryzen-5-cpu-16gb-ram-atg4k/ https://pinballcars.com/new-4k-virtual-pinball-machine-pc-vpx-rtx-5060-gpu-ryzen-5-cpu-16gb-ram-atg4k/#comments Wed, 29 Jul 2026 06:04:43 +0000 https://pinballcars.com/new-4k-virtual-pinball-machine-pc-vpx-rtx-5060-gpu-ryzen-5-cpu-16gb-ram-atg4k/ Continue reading: NEW 4K Virtual Pinball Machine PC VPX RTX 5060 GPU Ryzen 5 CPU 16gb RAM ATG4k]]>













Unfortunately the higher prices of PC components right now, ive had to raise my price to keep up. Thank Ai Datacenters for increasing the cost of chips at the consumer level. This is all 100% NEW BUILD. With RAM/SSD’s going up, Ive kept my pricing as low as i can, minus no case. This is on a wood plank, for pin-cab installation, if you want it in a case. (see the last photo for the new ZALMAN case i have available). PC SPECS (100% NEW). MSI Motherboard (supports a 2.1 audio setup, if you want to add SSF, you will need a usb 7.1 card). Ryzen 5 5500 6 core. 16GB OLOY RGB Gaming DDR4 RAM. PNY RTX 5060 Video Card (pic shows the last build with a msi card). Power Supply is a ThermalTake 500w. You have growing room with the CPU/GPU! This runs a a 4k 60hz playfield, and 2 additional screens, super smooth. This build is designed specifically for this setup, which you MUST have. 4k play field running 60hz. A 1080p backglass monitor. A 16:9 ratio 3rd screen for FULL DMD at 1366×768 (these 3 resolutions work perfect with a ATG 4K). (i can provide recommendations on screens if needed). NO USB MONITORS, must run though video card. Your screens need to remember the power state, so when you kill power, and apply power, they auto come on again. (all pc monitors do this, but some TV’s cant, and require a remote to power on each time). Screens must up and running before windows boots, or your screens re-arrange each time, and you have to re-configure. You have growing room even on this budget build, it runs everything currently released, near perfectly. Even On the most demanding vpin workshop tables, CPU and GPU handle all the current tables at full 60FPS. Every table will run pretty much stutter free, and never drops from 59-60FPS. (In a rare event of a lot of flashers, and ball movement, you may see slight ball stutter, Ive only seen it on the new DIE HARD). This machine can be sent to you in several different ways. BLANK, ready for you to install your own OS/Software. Clean OS install, ready for you to install pinball software. You have no idea where to start, and want me to take care of everything for you, and make your life as easy as possible.. Please shoot me a message and ask for details on what I can do for you. I provide good instructions and after sales support! (please see my feedback). Ive built 30 plus pincabs, Ive been working in IT for 20+ years. I want to sell this to someone that’s putting together a virtual pinball cabinet and needs a capable computer for a good deal, and can get up and going QUICK. Please be familiar with the programs that run all this, and have some decent computer skills, its not hard, but you need to know your way around windows. I have over a dozen customers use this with ATGAMES 4K Cabinets, this worked perfectly! For ATG4k, The buttons will use “XPADDER” from what Ive read, Wagners Tech Talk covers everything Atgames4k related, so i highly recommend his youtube channel! Here’s some info on my own setup, that I run on my own machine (and your setup can be the same as below). Latest baller installer, with VPX 10.7, beta7, latest 10.8, with the latest pinmame, b2s, and flex/ultra dmd. Im running DOF configured and working with my test setup (a sainsmart 8 relay board). Im very much on QUALITY over quantity, so I have about 300 of the latest tables. I have Colored rom support, (vni, pac, and the crz/serum, and new serum V2 format). All VPX and FP tables have had preview videos recorded for playfield, and backglass. That took me DAYS to do, this took a LOT of time getting about 700 videos recorded for pinup popper. The biggest part of this hobby is playing with everything and learning how it works. A backup Hard drive copy WILL BE INCLUDED. I recommend you make a full copy of the SSD drive, before you make any changes, this will save your life when you do updates and upgrades later on, if it goes sideways. I also sell plunger kits/input/nudge boards, i can discount that if bought at the same time.

]]> https://pinballcars.com/new-4k-virtual-pinball-machine-pc-vpx-rtx-5060-gpu-ryzen-5-cpu-16gb-ram-atg4k/feed/ 0 https://pinballcars.com/virtual-pinball-usb-controller-g2u/ https://pinballcars.com/virtual-pinball-usb-controller-g2u/#comments Tue, 16 Jun 2026 01:55:41 +0000 https://pinballcars.com/virtual-pinball-usb-controller-g2u/ Continue reading: Virtual Pinball USB Controller G2U]]>





Please check the item specifics as it may contain details which you are looking for. We offer a handpicked collection of high-quality items, available exclusively in the U. Check item specifics and photos to ensure you make the perfect choice. While we strive to offer detailed images, it’s not always possible to verify every aspect of the item. Therefore, we apologize if the product does not meet your expectations.

]]> https://pinballcars.com/virtual-pinball-usb-controller-g2u/feed/ 0 https://pinballcars.com/atgames-legends-pinball-digital-hd-screen-virtual-pinball-machine-no-legs/ https://pinballcars.com/atgames-legends-pinball-digital-hd-screen-virtual-pinball-machine-no-legs/#comments Sun, 14 Jun 2026 17:51:42 +0000 https://pinballcars.com/atgames-legends-pinball-digital-hd-screen-virtual-pinball-machine-no-legs/








New pcb board, works great, does not include legs, 41″ long, 36″ tall. If you have any questions do not hesitate to reach out. I will try to provide any advice or help you as best as I can. You will receive the exact item pictured as advertised. Thanks for browsing Kyler’s Hidden Gems!

]]> https://pinballcars.com/atgames-legends-pinball-digital-hd-screen-virtual-pinball-machine-no-legs/feed/ 0 https://pinballcars.com/ultimate-4k-virtual-pinball-guide-build-or-buy/ https://pinballcars.com/ultimate-4k-virtual-pinball-guide-build-or-buy/#comments Fri, 05 Jun 2026 00:31:34 +0000 https://pinballcars.com/ultimate-4k-virtual-pinball-guide-build-or-buy/ ]]> https://pinballcars.com/ultimate-4k-virtual-pinball-guide-build-or-buy/feed/ 0 https://pinballcars.com/virtual-pinball-backbox-kit-flat-pack-wpc-williams-widebody/ https://pinballcars.com/virtual-pinball-backbox-kit-flat-pack-wpc-williams-widebody/#comments Mon, 01 Jun 2026 00:16:42 +0000 https://pinballcars.com/virtual-pinball-backbox-kit-flat-pack-wpc-williams-widebody/ Continue reading: Virtual Pinball BACKBOX Kit Flat Pack WPC Williams WideBody]]>





Current build slots are open as of 5-18-26, no waiting. I started in this hobby over 14 years ago. Built dozens of cabinets, and even more PC’s for hobby enthusiasts around the country. I’ve bought flatpacks in the beginning, then i had access to a shopbot and started cutting my own cabinets. Now, i bought my own ALTMILL CNC, and im cutting my own cabinets for all of you to enjoy! I sell all sorts of vpin related things, so be sure to check out my other items! Cabinet Materials are 3/4 cabinet grade veneered plywood, very smooth and take vinyl and paint very well. Rear Panels are 1/2 to save weight. DMD Panel designed for 15.6-inch LCD DMD’s and 5.25 inch speakers. VESA mount panel for Backglass monitor included. 3pc Rear panels, with round vent holes on top, with mesh to cover holes. Removable rear backbox service door with cylinder lock/key included. Holes drilled in backbox for WPC Hinges (3 holes per side). If you dont have a widebody wpc cabinet, i can leave the bottom holes for the hinges OFF, so you can position them yourself. This is a LIGHT woodworking project, you will need glue, clamps, carpenter square for nice 90’s, some sandpaper, etc. There is VERY LITTLE sanding needed for just a backbox, its goes together very nicely.

]]> https://pinballcars.com/virtual-pinball-backbox-kit-flat-pack-wpc-williams-widebody/feed/ 0 https://pinballcars.com/wpc-williams-wide-body-style-virtual-pinball-cabinet-kit-flat-pack/ https://pinballcars.com/wpc-williams-wide-body-style-virtual-pinball-cabinet-kit-flat-pack/#comments Thu, 30 Apr 2026 03:14:44 +0000 https://pinballcars.com/wpc-williams-wide-body-style-virtual-pinball-cabinet-kit-flat-pack/ Continue reading: WPC Williams Wide Body Style Virtual Pinball Cabinet Kit Flat Pack]]>













Current build slots are open on april 26th. I’m proud to offer full size WPC/Williams widebody cabinets. These are not shortened down/resized, its the FULLSIZE, and all OEM hardware fits exactly as it should (side rails, lockdown bar and receiver, coin door etc). I started in this hobby over 14 years ago. Built dozens of cabinets, and even more PC’s for hobby enthusiasts around the country. I’ve bought flatpacks in the beginning, then i had access to a shopbot and started cutting my own cabinets. Now, i bought my own ALTMILL CNC, and im cutting my own cabinets for all of you to enjoy! I sell all sorts of vpin related things, so be sure to check out my other items! I included a assembled photo of the last standard width cabinet i did, it was a standard width lower, and standard width backbox (37″ playfield and a 27″ backbox, i dont usually do std width cabs anymore). The raw widebody cabinet in the pic is sitting, just leaned together, not glued yet, as it goes together like legos! The backbox is slightly WIDER than standard, due to most people wanting to fit 32 screens in the backbox. (you have 29.5 inside width in backbox). NO SCREWS OR NAILS NEEDED! Goes together with just wood glue. Cabinet Materials are 3/4 cabinet grade veneered plywood, very smooth and take vinyl and paint very well. Some panels are 1/2 to reduce weight, like backbox rear access panels. I use maple/oak/birch plywood for my wood source. Pics show some parts with black paint, theses were in build stage, you will receive raw wood, ready for paint and graphics. Playfield mount is now included in full cabinet kits! Button holes for flipper Buttons, Start, Extra Ball, Exit, Launch Button, and plunger cutout. (see photo for spacing/layout). Coin Door Cutout, and bolt holes pre-drilled. Hole for a down firing 8 sub. 1 button hole on bottom for power. Corners are CNC’d out for leg bolts to fit perfectly. T-Slots are cut in the sides for playfield glass side rails. Rear of cabinet has 2 holes for 120mm fans, and a power connector. Vertical panel where a led panel or lights would hang, below the rear glass channel location. This cabinet is made to line up with the williams corner mount leg brackets. DMD Panel designed for 15.6-inch LCD DMD’s and 5.25 inch speakers (holes or slots for speakers). I have attached a photo of a dmd panel with 4 speakers, for reference, can be customized! VESA mount panel for Backglass monitor included. Rear panels, with round vent holes on top, with mesh to cover holes. Removable rear service door with cylinder lock/key included. Holes drilled in backbox for WPC Hinges (3 holes per side) and the 2 pivot holes in the cabinet. If you DONT need a dmd panel, i can offer a small discount on parts you dont need. I can DELETE any holes/cuts free of charge. This is a LIGHT woodworking project, you will need glue, clamps, carpenter square for nice 90’s, some sandpaper, etc. There is VERY LITTLE sanding, due to thickness of wood varying, the edges of the cabinet usually need some light sanding where the joints are. 733 thickness it seems, so a variance of. 037 You will want to lightly go over the whole cab, to get super smooth before getting ready for vinyl graphics. Currently no backlog on orders!

]]> https://pinballcars.com/wpc-williams-wide-body-style-virtual-pinball-cabinet-kit-flat-pack/feed/ 0 https://pinballcars.com/budget-4k-virtual-pinball-machine-pc-vpx-rtx-2070-gpu-9th-gen-i7-cpu-16gb-atg4k/ https://pinballcars.com/budget-4k-virtual-pinball-machine-pc-vpx-rtx-2070-gpu-9th-gen-i7-cpu-16gb-atg4k/#comments Fri, 10 Apr 2026 02:14:45 +0000 https://pinballcars.com/budget-4k-virtual-pinball-machine-pc-vpx-rtx-2070-gpu-9th-gen-i7-cpu-16gb-atg4k/ Continue reading: BUDGET 4K Virtual Pinball Machine PC VPX RTX 2070 GPU 9th gen i7 CPU 16gb ATG4k]]>












Setup Fresh Windows 11 Pro MAR 2026! This Was a lightly used Alienware R8, converted for Vpin use! Alienware Aurora R8 (water cooled CPU). Intel i7 9700 CPU. 512GB NVME (also has a 3.5 slot, and 2x 2.5 slots for more hard drive expansion). (dell/alienware has a downloadable control center to change the LED’s on the case). Please note, you must provide your own screens, this is ONLY the computer tower. This runs a a 4k 60hz playfield, and 2 additional screens, super smooth. This build is designed specifically for this setup, which you MUST have. 4k play field running 60hz. A 1080p backglass monitor. A 16:9 ratio 3rd screen for FULL DMD at 1366×768 (these 3 resolutions work perfect with a ATG 4K). (i can provide recommendations on screens if needed). NO USB MONITORS, must run though video card. Your screens need to remember the power state, so when you kill power, and apply power, they auto come on again. (all pc monitors do this, but some TV’s cant, and require a remote to power on each time). Screens must up and running before windows boots, or your screens re-arrange each time, and you have to re-configure. You have growing room even on this budget build, it runs everything currently released, near perfectly. Even On the most demanding vpinworkshop tables, CPU and GPU handle all the current tables at full 60FPS. Every table will run pretty much stutter free, and never drops from 59-60FPS. (In a rare event of a lot of flashers, and ball movement, you may see slight ball stutter, Ive only seen it on the new DIE HARD). This machine can be sent to you in several different ways. BLANK, ready for you to install your own OS/Software. Clean os install, ready for you to install pinball software. You have no idea where to start, and want me to take care of everything for you, and make your life as easy as possible.. Please shoot me a message and ask for details on what I can do for you. I provide good instructions and after sales support! (please see my feedback). Ive built 30 plus pincabs, Ive been working in IT for 20+ years. I want to sell this to someone that’s putting together a virtual pinball cabinet and needs a capable computer for a good deal, and can get up and going QUICK. Please be familiar with the programs that run all this, and have some decent computer skills, its not hard, but you need to know your way around windows. I have over a dozen people use this with ATGAMES 4K Cabinets, this worked perfectly! For ATG4k, The buttons will use “XPADDER” from what Ive read, Wagners Tech Talk covers everything Atgames4k related, so i highly recommend his youtube channel! Here’s some info on my own setup, that I run on my own machine. I do the L. Atest baller installer, with VPX 10.7, 10.8, with the latest pinmame, b2s, and flex/ultra dmd. I run Future Pinball to play the amazing pinevent tables (about 10 of them). Im running DOF configured and working with my test setup (a sainsmart 8 relay board). Im very much on QUALITY over quantity, so I have about 300 of the latest tables for myself. I have Colored rom support, (vni, pac, and the crz/serum, and new serum V2 format). All VPX and FP tables have had preview videos recorded for playfield, and backglass. That took me DAYS to do, this took a LOT of time getting about 700 videos recorded for pinup popper. As far as this machine goes. You need to be decent at using computers, installing games and software, basic use and understanding, this is 7 or 8 programs all working together the best they can, and you will have to make adjustments, troubleshoot, and so on, over time, as needed, when owning a vpin cabinet. The biggest part of this hobby is playing with everything and learning how it works. A backup Hard drive copy WILL BE INCLUDED. I recommend you make a full copy of the SSD drive, before you make any changes, this will save your life when you do updates and upgrades later on, if it goes sideways. I also sell plunger kits/input/nudge boards, i can discount that if bought at the same time.

]]> https://pinballcars.com/budget-4k-virtual-pinball-machine-pc-vpx-rtx-2070-gpu-9th-gen-i7-cpu-16gb-atg4k/feed/ 0 https://pinballcars.com/new-4k-virtual-pinball-machine-pc-vpx-rtx-4060-gpu-ryzen-5-cpu-16gb-ram-atg4k/ https://pinballcars.com/new-4k-virtual-pinball-machine-pc-vpx-rtx-4060-gpu-ryzen-5-cpu-16gb-ram-atg4k/#comments Tue, 07 Apr 2026 10:06:43 +0000 https://pinballcars.com/new-4k-virtual-pinball-machine-pc-vpx-rtx-4060-gpu-ryzen-5-cpu-16gb-ram-atg4k/ Continue reading: NEW 4K Virtual Pinball Machine PC VPX RTX 4060 GPU Ryzen 5 CPU 16gb RAM ATG4k]]>













Unfortunately the higher prices of PC components right now, ive had to raise my price to keep up. Thank Ai Datacenters for increasing the cost of chips at the consumer level. This is all 100% NEW BUILD. With RAM/SSD’s going up, Ive kept my pricing as low as i can, minus no case. This is on a wood plank, for pin-cab installation, if you want it in a case. (see the last photo for the new ZALMAN case i have available). MSI Motherboard (supports a 2.1 audio setup, if you want to add SSF, you will need a usb 7.1 card). Ryzen 5 5500 6 core. 16GB TeamGroup Vulcan DDR4 RAM. MSI 4060 Video Card. Power Supply is a ThermalTake 500w. You have growing room with the CPU/GPU, and can easily upgrade video cards down the road as 5000 cards series become cheaper. This runs a a 4k 60hz playfield, and 2 additional screens, super smooth. This build is designed specifically for this setup, which you MUST have. 4k play field running 60hz. A 1080p backglass monitor. A 16:9 ratio 3rd screen for FULL DMD at 1366×768 (these 3 resolutions work perfect with a ATG 4K). (i can provide recommendations on screens if needed). NO USB MONITORS, must run though video card. Your screens need to remember the power state, so when you kill power, and apply power, they auto come on again. (all pc monitors do this, but some TV’s cant, and require a remote to power on each time). Screens must up and running before windows boots, or your screens re-arrange each time, and you have to re-configure. You have growing room even on this budget build, it runs everything currently released, near perfectly. Even On the most demanding vpin workshop tables, CPU and GPU handle all the current tables at full 60FPS. Every table will run pretty much stutter free, and never drops from 59-60FPS. (In a rare event of a lot of flashers, and ball movement, you may see slight ball stutter, Ive only seen it on the new DIE HARD). This machine can be sent to you in several different ways. BLANK, ready for you to install your own OS/Software. Clean os install, ready for you to install pinball software. You have no idea where to start, and want me to take care of everything for you, and make your life as easy as possible.. Please shoot me a message and ask for details on what I can do for you. I provide good instructions and after sales support! (please see my feedback). Ive built 30 plus pincabs, Ive been working in IT for 20+ years. I want to sell this to someone that’s putting together a virtual pinball cabinet and needs a capable computer for a good deal, and can get up and going QUICK. Please be familiar with the programs that run all this, and have some decent computer skills, its not hard, but you need to know your way around windows. I have over a dozen customers use this with ATGAMES 4K Cabinets, this worked perfectly! For ATG4k, The buttons will use “XPADDER” from what Ive read, Wagners Tech Talk covers everything Atgames4k related, so i highly recommend his youtube channel! Here’s some info on my own setup, that I run on my own machine. Latest baller installer, with VPX 10.7, beta7, latest 10.8, with the latest pinmame, b2s, and flex/ultra dmd. Im running DOF configured and working with my test setup (a sainsmart 8 relay board). Im very much on QUALITY over quantity, so I have about 300 of the latest tables. I have Colored rom support, (vni, pac, and the crz/serum, and new serum V2 format). All VPX and FP tables have had preview videos recorded for playfield, and backglass. That took me DAYS to do, this took a LOT of time getting about 700 videos recorded for pinup popper. As far as this machine goes. You need to be decent at using computers, installing games and software, basic use and understanding, this is 7 or 8 programs all working together the best they can, and you will have to make adjustments, troubleshoot, and so on, over time, as needed, when owning a vpin cabinet. The biggest part of this hobby is playing with everything and learning how it works. A backup Hard drive copy WILL BE INCLUDED. I recommend you make a full copy of the SSD drive, before you make any changes, this will save your life when you do updates and upgrades later on, if it goes sideways. I also sell plunger kits/input/nudge boards, i can discount that if bought at the same time.

]]> https://pinballcars.com/new-4k-virtual-pinball-machine-pc-vpx-rtx-4060-gpu-ryzen-5-cpu-16gb-ram-atg4k/feed/ 0